|
Kto jest w sklepie?
Sklep przegląda 5475 gości
|
Kategorie
|
Informacje
|
Polecamy
|
|
|
|
|
Dla tego produktu nie napisano jeszcze recenzji!
Programming the Remote
To erase all codes that have been programmed to all devices in the remote, follow these steps: 1. Press any Input Selector 456 and also the Learn button 7. 2. When the red LED under the Input Selector turns red and the Program/SPL Indicator 2 flashes amber, release the buttons. 3. Press and release the same Input Selector 456 again. 4. Press the 9 button H three times. 5. The Program/SPL Indicator 2 will turn off and the red light under the Input Selector will flash on and off once to indicate that the codes have been erased.
Macro Programming
Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the AVR 5000�s remote control. Once programmed, a macro will send out up to 19 different remote codes in a pre-determined sequential order enabling you to automate the process of turning on your system, changing devices, or other common tasks. The AVR�s remote can store up to five separate macro command sequences, one that is associated with the Power On button 0, and four more that are accessed by pressing the Macro buttons M. 1. Press the Mute button b and the Macro button M to be programmed or the PowerOn button 0 at the same time. Note that the latest selected Input Selector will light red, and the Program/SPL Indicator 2 will flash amber. 2. Enter the steps for the macro sequence by pressing the button for the actual command step. Although the macro may contain up to 19 steps, each button press, including those used to change devices, counts as a step. The Program/SPL Indicator 2 will flash green to confirm each button press as you enter commands. NOTE: While entering commands for Power On of any device during a macro sequence, press the Mute button b. DO NOT press the actual Power ON button. � Remember to press the appropriate Input Selector button 4 before functions are changed to another device. This is also needed for the AVR Selector button 5 itself, as long as it�s not lit red and AVR functions shall be programmed. 3. When all the steps have been entered, press the Sleep button 9 to enter the commands. The red light under the Input Selector 45 will blink and then turn off. Example: To program the Macro 1 M button so that it turns on the AVR 5000, TV and a SatReceiver, follow these steps: � Press the Macro 1 button M and Mute b buttons at the same time and then release them. � Note that the Program/SPL Indicator will flash amber. � Press the AVR Selector 5. � Press the Mute b button to store the AVR�s power on command. � Press the VID 2 Input Selector button 4 to indicate the next command is for �TV Power On.� � Press the Mute b button to store the TV Power On Command.
� Press the VID 3 Input Selector button 4 to indicate the next command is for �SatReceiver Power On.� � Press the Mute b button to store the SatReceiver Power On command. � Press the Sleep/Channel Up button 9 to complete the process and store the macro sequence. After following these steps, each time you press the Macro 1 button M, the remote will send all Power On commands. Erasing Macro Commands To remove the commands that have been programmed into one of the Macro buttons, follow these steps: 1. Press the Mute button b and the Macro button M that contains the commands you wish to erase. 2. Note that the Program/SPL Indicator 2 will flash amber, and the LED under the AVR Selector 5 will turn red. 3. Within ten seconds, press the Surround Mode Selector/Channel Down button A. 4. The red LED under the AVR Selector will go out, and the Program/SPL Indicator 2 will turn green and flash three times before it goes out. 5. When the Program/SPL Indicator 2 goes out, the Macro has been erased.
PROGRAMMING THE REMOTE 41
|
|
|
> |
|